The Axicube One Sharpening Angle Finder (Rev 2) is designed for high-precision measurement of angles between planes and the inclination of a surface from the horizontal and vertical levels. MEMS (Micro Electro Mechanical System) technology with ultra-precise electronic sensors of inclination relative to the gravity vector.
Features
- MEMS design (Micro Electro Mechanical System) with ultra-precise electronic sensors of inclination relative to the gravity vector
- Compact aluminum shell
- N38 class neodymium magnets on the bottom, lateral, and rear sides
- Built-in battery chargeable via the Micro-USB connector
Specification
- Angle measurement range: 0 – 99.9°
- Measurement accuracy: 0.1°
- Measurement error: 0.05°
- Battery Capacity: 300mAh
- Charging time: 3-5 hours
- Auto power-off: 5 minutes
- Dimensions: 18.3 x 30.6 x 45.8 mm.
- Weight: 60 grams
- Weight with packaging: 140 grams
Kit
- Axicube One Electronic Angle Finder
- Micro USB cable
- User manual
How to use Axicube One
General Information

1 Power button | 2 Reset button | 3 Display | 4 Divider | 5 Micro-USB | A
Axicube will go sleep after 5 minutes of inactivity. Press once to turn it on. To turn it off, hold for 3 sec.
To check the battery charge level and the current mode, press when Axicube is on. 85:P2 – charge level 85%, P2 mode.
To cycle operating modes, press and at the same time.
Do not let the battery level drop to 0% level. The battery level below 10% is critical – the Axicube must be immediately charged. The full charging time is 3-5 hours.
Axicube One Modes
- P1 – Inclinometer Mode for measuring the angle of inclination from horizontal level
- P2 – Universal Mode (Kadet/Blitz mode) dual-purpose: 1) for setting the sharpening angle on Kadet and Blitz systems, and 2) for measuring the sharpening angle on a wide range of sharpening systems
- P3 – K03 Mode for measuring the sharpening angle on sharpening systems with horizontally leveled knife
- P4 – Angle Gauge Mode for setting sharpening angle at the beginning of sharpening session
P1 Inclinometer Mode
00:00 The inclinometer mode is designed to measure the angle of inclination relative to the horizontal level.
️Calibration
- Place Axicube on a flat surface.
- Press and hold for 15 s. The display will start flashing.
- Release . The display will show P1
- Place Axicube against a stationary point, such as a wall.
- Press . The display will show P2
- Turn Axicube 180°. Press ⊙ one more time.
P2 Universal Mode with Kadet and Blitz
0:00 Universal mode is designed for sharpening systems other than TSPROF K03. On Kadet and Blitz series, setting the sharpening angle and measuring the sharpening angle are executed in different ways.
️Setting the sharpening angle
- Make your system ready for a sharpening session. Put the guide rod with a sharpening stone facing down on top of the clamped knife.
- Place the Axicube side A on the stone holder.
- Reset to zero. . #.## → 0:00
- Place the Axicube side A on the angle finder stand.
- Set a desired sharpening angle.
Measuring the sharpening angle
- Place the Axicube side A on the angle gauge holder.
- Reset to zero. . #.## → 0:00
- Place the Axicube side A on the abrasive holder.
- Axicube will correctly measure a sharpening angle at any point of the blade.
P2 Universal Mode with non-TSPROF systems
0:00 Universal mode is designed for sharpening systems other than TSPROF K03.
️Setting the sharpening angle
- Make your system ready for a sharpening session. Put the guide rod with a sharpening stone facing down on top of the clamped knife.
- Place the Axicube on the zero level. Use the same side of Axicube for leveling and measuring.
- Reset to zero. Press . #.## → 0:00
- Place the Axicube on the stone holder.
- Set a desired sharpening angle.
Measuring the sharpening angle
- Place the Axicube on the zero level. Use the same side of Axicube for leveling and measuring.
- Reset to zero. Press . #.## → 0:00
- Place the Axicube on the stone holder.
- Axicube will correctly measure a sharpening angle at any point of the blade.
P3 K03 Mode
0:00 K03 mode is designed for K03 family but will work with any sharpening systems with horizontally leveled knife. P3 mode is demanding but rewarding.
Measuring the sharpening angle
- Place the Axicube on the zero level. Use the same side of Axicube for leveling and measuring.
- Reset to zero. Press ⊙. #.## → 0:00
- ERR9 occurs in P3 mode when you try to zero reset not in the horizontal level.
- Place the Axicube on the stone holder.
- Axicube will correctly measure a sharpening angle at any point of the blade.
P4 Angle Gauge Mode
000:0 Angle Gauge mode mimics traditional angle cubes. Designed for domestic repair, construction and equipment adjustment.
Finding the angle
- Place Axicube side A on the first surface.
- Reset to zero. Press ⊙. ###.# → 000:0
- Place the Axicube side A on the second surface.
- Axicube will correctly measure a sharpening angle at any point of the blade.






![Anodized Aluminum Blank [160 x 25 x 5mm] [6" x 1"] 13 Tian 20Series 20160 20x 2025 20x 203 20 Gray 088a1af3 ed73 4c51 ad5b f02c0174fc6d](https://cdn.shopify.com/s/files/1/0984/5900/files/Tian_20Series_20160_20x_2025_20x_203_20_Gray_088a1af3-ed73-4c51-ad5b-f02c0174fc6d.jpg?v=1750305890)



